Environmental impact of electricity generation / REF / 613 / 2014

The environmental impact of electricity generation is significant because modern society uses large amounts of electrical power. This power is normally generated at power plants that convert some other kind of energy into electrical power. Each system has advantages and disadvantages, but many of them pose environmental concerns.

Water usage

The amount of water usage is often of great concern for electricity generating systems as populations increase and droughts become a concern. Still, according to the U.S. Geological Survey, thermoelectric power generation accounts for only 3.3 percent of net freshwater consumption with over 80 percent going to irrigation. Likely future trends in water consumption are covered here. General numbers for fresh water usage of different power sources are shown below.

	Water usage (gal/MW-h)
Power source	Low case	Medium/Average case	High case
Nuclear power	400 (once-through cooling)	400 to 720 (pond cooling)	720 (cooling towers)
Coal	300		480
Natural gas	100 (once-through cycle)		180 (with cooling towers)
Hydroelectricity		1,430
Solar thermal		1,060
Geothermal	1,800		4,000
Biomass	300		480
Solar photovoltaic		30
Wind power	.5	1	2.2

Steam-cycle plants (nuclear, coal, NG, solar thermal) require a great deal of water for cooling, to remove the heat at the steam condensors. The amount of water needed relative to plant output will be reduced with increasing boiler temperatures. Coal- and gas-fired boilers can produce high steam temperatures and so are more efficient, and require less cooling water relative to output. Nuclear boilers are limited in steam temperature by material constraints, and solar is limited by concentration of the energy source.

Thermal cycle plants near the ocean have the option of using seawater. Such a site will not have cooling towers and will be much less limited by environmental concerns of the discharge temperature since dumping heat will have very little effect on water temperatures. This will also not deplete the water available for other uses. Nuclear power in Japan for instance, uses no cooling towers at all because all plants are located on the coast. If dry cooling systems are used, significant water from the water table will not be used. Other, more novel, cooling solutions exist, such as sewage cooling at the Palo Verde Nuclear Generating Station.

Hydroelectricity's main cause of water usage is both evaporation and seepage into the water table.

Reference: Nuclear Energy Institute factsheet using EPRI data and other sources.hOE

Source(s): Adapted from US Department Of Energy, Energy Demand on Water Resources. Report to Congress on the Interdependence of Energy and Water, December 2006 (except where noted).
*Cambridge Energy Research Associates (CERA) estimate. #Educated estimate.
Water Requirements for Existing and Emerging Thermoelectric Plant Technologies. US Department Of Energy, National Energy Technology Laboratory, August 2008.
Note(s): 3.6 GJ = gigajoule(s) == 1 MW·h = megawatt-hour(s), thus 1 L/GJ = 3.6 L/MW·h. B = Black coal (supercritical)-(new subcritical), Br = Brown coal (new subcritical), H = Hard coal, L = Lignite, cc = combined cycle, oc = open cycle, T_L = low-temperature/closed-circuit (geothermal doublet), T_H = high-temperature/open-circuit.

Fossil fuels

Most electricity today is generated by burning fossil fuels and producing steam which is then used to drive a steam turbine that, in turn, drives an electrical generator.

Such systems allow electricity to be generated where it is needed, since fossil fuels can readily be transported. They also take advantage of a large infrastructure designed to support consumer automobiles. The world's supply of fossil fuels is large, but finite. Exhaustion of low-cost fossil fuels will have significant consequences for energy sources as well as for the manufacture of plastics and many other things. Various estimates have been calculated for exactly when it will be exhausted (see Peak oil). New sources of fossil fuels keep being discovered, although the rate of discovery is slowing while the difficulty of extraction simultaneously increases.

More serious are concerns about the emissions that result from fossil fuel burning. Fossil fuels constitute a significant repository of carbon buried deep underground. Burning them results in the conversion of this carbon to carbon dioxide, which is then released into the atmosphere. The estimated CO2 emission from the world's electrical power industry is 10 billion tonnes yearly.^[16] This results in an increase in the Earth's levels of atmospheric carbon dioxide, which enhances the greenhouse effect and contributes to global warming. The linkage between increased carbon dioxide and global warming is well accepted, though fossil-fuel producers vigorously contest these findings.

Flue-gas stacks at Ekibastuz GRES-1 Power Plant in Ekibastus, Kazakhstan are 330 meters tall

Depending on the particular fossil fuel and the method of burning, other emissions may be produced as well. Ozone, sulfur dioxide, NO₂ and other gases are often released, as well as particulate matter. Sulfur and nitrogen oxides contribute to smog and acid rain. In the past, plant owners addressed this problem by building very tall flue-gas stacks, so that the pollutants would be diluted in the atmosphere. While this helps reduce local contamination, it does not help at all with global issues.

Fossil fuels, particularly coal, also contain dilute radioactive material, and burning them in very large quantities releases this material into the environment, leading to low levels of local and global radioactive contamination, the levels of which are, ironically, higher than a nuclear power station as their radioactive contaminants are controlled and stored.

Coal also contains traces of toxic heavy elements such as mercury, arsenic and others. Mercury vaporized in a power plant's boiler may stay suspended in the atmosphere and circulate around the world. While a substantial inventory of mercury exists in the environment, as other man-made emissions of mercury become better controlled, power plant emissions become a significant fraction of the remaining emissions. Power plant emissions of mercury in the United States are thought to be about 50 tons per year in 2003, and several hundred tons per year in China. Power plant designers can fit equipment to power stations to reduce emissions.

According to Environment Canada:

"The electricity sector is unique among industrial sectors in its very large contribution to emissions associated with nearly all air issues. Electricity generation produces a large share of Canadian nitrogen oxides and sulphur dioxide emissions, which contribute to smog and acid rain and the formation of fine particulate matter. It is the largest uncontrolled industrial source of mercury emissions in Canada. Fossil fuel-fired electric power plants also emit carbon dioxide, which may contribute to climate change. In addition, the sector has significant impacts on water and habitat and species. In particular, hydro dams and transmission lines have significant effects on water and biodiversity."

Coal mining practices in the United States have also included strip mining and removing mountain tops. Mill tailings are left out bare and have been leached into local rivers and resulted in most or all of the rivers in coal producing areas to run red year round with sulfuric acid that kills all life in the rivers.

The efficiency of some of these systems can be improved by cogeneration and geothermal (combined heat and power) methods. Process steam can be extracted from steam turbines. Waste heat produced by thermal generating stations can be used for space heating of nearby buildings. By combining electric power production and heating, less fuel is consumed, thereby reducing the environmental effects compared with separate heat and power systems.

Nuclear power

Nuclear power plants do not burn fossil fuels and so do not directly emit carbon dioxide; because of the high energy yield of nuclear fuels, the carbon dioxide emitted during mining, enrichment, fabrication and transport of fuel is small when compared with the carbon dioxide emitted by fossil fuels of similar energy yield.

A large nuclear power plant may reject waste heat to a natural body of water; this can result in undesirable increase of the water temperature with adverse effect on aquatic life.

Emission of radioactivity from a nuclear plant is controlled by regulations. Abnormal operation may result in release of radioactive material on scales ranging from minor to severe, although these scenarios are very rare.

Mining of uranium ore can disrupt the environment around the mine. Disposal of spent fuel is controversial, with many proposed long-term storage schemes under intense review and criticism. Diversion of fresh or spent fuel to weapons production presents a risk of nuclear proliferation. Finally, the structure of the reactor itself becomes radioactive and will require decades of storage before it can be economically dismantled and in turn disposed of as waste.

Renewable energy

Hydroelectric power

Development of large-scale hydroelectric power has environmental impacts associated with the change in water flow and the impoundment of water in a reservoir. Dams may block the passage of fish. The natural flow of silt down the river will be interrupted, affecting downstream ecosystems. Where large reservoirs are not cleared of trees before flooding, the methane gas released by decaying wood can be comparable in greenhouse effect to the CO2 emissions of a fossil-fuel plant of similar output. The filling of large reservoirs can induce earth tremors, which may be large enough to be objectionable or destructive. For example, the 1967 Koynanagar earthquake of 6.9 magnitude was created after the filling of the Koyna Dam in India, with 180 fatalities. A magnitude 7.9 earthquake near the Zipingpu Dam, China, in 2004, with 70,000 fatalities may also have been triggered by the weight of the reservoir.

Hydroelectric power facilities also create conditions where methylation occurs in the reservoir areas. The mechanism of methylation that results in elevated levels of methylmercury concentrations, is not fully understood at this time. Current theories revolve around anaerobic bacteria in oxygen-deprived layers of water converting elemental mercury to methylmercury, which is more readily absorbed into the food chain and other organisms.

Marine and Hydrokinetic (MHK)

Wave

Solar energy from the sun creates temperature differentials that result in wind. The interaction between wind and the surface of water creates waves, which are larger when there is a greater distance for them to build up. Wave energy potential is greatest between 30° and 60° latitude in both hemispheres on the west coast because of the global direction of wind. When evaluating wave energy as a technology type, it is important to distinguish between the four most common approaches: point absorber buoys, surface attenuators, oscillating water columns, and overtopping devices.

Point Absorber Buoy

This device floats on the surface of the water, held in place by cables connected to the seabed. Buoys use the rise and fall of swells to drive hydraulic pumps and generate electricity. EMF generated by electrical transmission cables and acoustic of these devices may be a concern for marine organisms. The presence of the buoys may affect fish, marine mammals, and birds as potential minor collision risk and roosting sites. Potential also exists for entanglement in mooring lines. Energy removed from the waves may also affect the shoreline, resulting in a recommendation that sites remain a considerable distance from the shore.

Surface Attenuator

These devices act similarly to point absorber buoys, with multiple floating segments connected to one another and are oriented perpendicular to incoming waves. A flexing motion is created by swells that drive hydraulic pumps to generate electricity. Environmental effects are similar to those of point absorber buoys, with an additional concern that organisms could be pinched in the joints.

Oscillating Water Column

Oscillating water column devices can be located on shore or in deeper waters offshore. With an air chamber integrated into the device, swells compress air in the chambers forcing air through an air turbine to create electricity. Significant noise is produced as air is pushed through the turbines, potentially affecting birds and other marine organisms within the vicinity of the device. There is also concern about marine organisms getting trapped or entangled within the air chambers.

Overtopping Device

Overtopping devices are long structures that use wave velocity to fill a reservoir to a greater water level than the surrounding ocean. The potential energy in the reservoir height is then captured with low-head turbines. Devices can be either on shore or floating offshore. Floating devices will have environmental concerns about the mooring system affecting benthic organisms, organisms becoming entangled, or EMF effects produced from subsea cables. There is also some concern regarding low levels of turbine noise and wave energy removal affecting the nearfield habitat.

Oscillating Wave Surge Converter

These devices typically have one end fixed to a structure or the seabed while the other end is free to move. Energy is collected from the relative motion of the body compared to the fixed point. Oscillating wave surge converters often come in the form of floats, flaps, or membranes. Environmental concerns include minor risk of collision, artificial reefing near the fixed point, EMF effects from subsea cables, and energy removal effecting sediment transport.

Tidal

Tidal Turbines

Land constrictions such as straits or inlets can create high velocities at specific sites, which can be captured with the use of turbines. These turbines can be horizontal, vertical, open, or ducted and are typically placed near the bottom of the water column.

The main environmental concern with tidal energy is associated with blade strike and entanglement of marine organisms as high speed water increases the risk of organisms being pushed near or through these devices. As with all offshore renewable energies, there is also a concern about how the creation of EMF and acoustic outputs may affect marine organisms. Because these devices are in the water, the acoustic output can be greater than those created with offshore wind energy. Depending on the frequency and amplitude of sound generated by the tidal energy devices, this acoustic output can have varying effects on marine mammals (particularly those who echolocate to communicate and navigate in the marine environment such as dolphins and whales). Tidal energy removal can also cause environmental concerns such as degrading farfield water quality and disrupting sediment processes. Depending on the size of the project, these effects can range from small traces of sediment build up near the tidal device to severely affecting nearshore ecosystems and processes.

Tidal Barrage

Tidal barrages are dams built across the entrance to a bay or estuary that captures potential tidal energy with turbines similar to a conventional hydrokinetic dam. Energy is collected while the height difference on either side of the dam is greatest, at low or high tide. A minimum height fluctuation of 5 meters is required to justify the construction, so only 40 locations worldwide have been identified as feasible.

Installing a barrage may change the shoreline within the bay or estuary, affecting a large ecosystem that depends on tidal flats. Inhibiting the flow of water in and out of the bay, there may also be less flushing of the bay or estuary, causing additional turbidity (suspended solids) and less saltwater, which may result in the death of fish that act as a vital food source to birds and mammals. Migrating fish may also be unable to access breeding streams, and may attempt to pass through the turbines. The same acoustic concerns apply to tidal barrages. Decreasing shipping accessibility can become a socio-economic issue, though locks can be added to allow slow passage. However, the barrage may improve the local economy by increasing land access as a bridge. Calmer waters may also allow better recreation in the bay or estuary.

Tidal Lagoon

A newer tidal energy design option is to construct circular retaining walls embedded with turbines that can capture the potential energy of tides. The created reservoirs are similar to those of tidal barrages, except that the location is artificial and does not contain a preexisting ecosystem.

Environmentally, the main concerns are blade strike on fish attempting to enter the lagoon, acoustic output from turbines, and changes in sedimentation processes. However, all these effects are localized and do not affect the entire estuary or bay.

Biomass

Electrical power can be generated by burning anything which will combust. Some electrical power is generated by burning crops which are grown specifically for the purpose. Usually this is done by fermenting plant matter to produce ethanol, which is then burned. This may also be done by allowing organic matter to decay, producing biogas, which is then burned. Also, when burned, wood is a form of biomass fuel.

Burning biomass produces many of the same emissions as burning fossil fuels. However, growing biomass captures carbon dioxide out of the air, so that the net contribution to global atmospheric carbon dioxide levels is small.

The process of growing biomass is subject to the same environmental concerns as any kind of agriculture. It uses a large amount of land, and fertilizers and pesticides may be necessary for cost-effective growth. Biomass that is produced as a by-product of agriculture shows some promise, but most such biomass is currently being used, for plowing back into the soil as fertilizer if nothing else.

Wind power

Onshore Wind

Wind power harnesses mechanical energy from the constant flow of air over the surface of the earth. Wind power stations generally consist of wind farms, fields of wind turbines in locations with relatively high winds. A primary publicity issue regarding wind turbines are their older predecessors, such as the Altamont Pass Wind Farm in California. These older, smaller, wind turbines are rather noisy and densely located, making them very unattractive to the local population. The downwind side of the turbine does disrupt local low-level winds. Modern large wind turbines have mitigated these concerns, and have become a commercially important energy source. Many homeowners in areas with high winds and expensive electricity set up small windmills to reduce their electric bills.

A modern wind farm, when installed on agricultural land, has one of the lowest environmental impacts of all energy sources:

• It occupies less land area per kilowatt-hour (kWh) of electricity generated than any other renewable energy conversion system, and is compatible with grazing and crops.
• It generates the energy used in its construction within just months of operation.
• Greenhouse gas emissions and air pollution produced by its construction are small and declining. There are no emissions or pollution produced by its operation.
• Modern wind turbines rotate so slowly (in terms of revolutions per minute) that they are rarely a hazard to birds.

Landscape and heritage issues may be a significant issue for certain wind farms. However, when appropriate planning procedures are followed, the heritage and landscape risks should be minimal. Some people may still object to wind farms, perhaps on the grounds of aesthetics, but there is still the supportive opinions of the broader community and the need to address the threats posed by climate change.

Offshore Wind

Offshore wind is similar to terrestrial wind technologies, as a large windmill-like turbine located in a fresh or saltwater environment. Wind causes the blades to rotate, which is then turned into electricity and connected to the grid with cables. The advantages of offshore wind are that winds are stronger and more consistent, allowing turbines of much larger size to be erected by vessels. The disadvantages are the difficulties of placing a structure in a dynamic ocean environment.

The turbines are often scaled-up versions of existing land technologies. However, the foundations are unique to offshore wind and are listed below:

Monopile Foundation

Monopile foundations are used in shallow depth applications (0–30 m) and consist of a pile being driven to varying depths into the seabed (10–40 m) depending on the soil conditions. The pile-driving construction process is an environmental concern as the noise produced is incredibly loud and propagates far in the water, even after mitigation strategies such as bubble shields, slow start, and acoustic cladding. The footprint is relatively small, but may still cause scouring or artificial reefs. Transmission lines also produce an electromagnetic field that may be harmful to some marine organisms.

Tripod Fixed Bottom

Tripod fixed bottom foundations are used in transitional depth applications (20–80 m) and consist of three legs connecting to a central shaft that supports the turbine base. Each leg has a pile driven into the seabed, though less depth is necessary because of the wide foundation. The environmental effects are a combination of those for monopile and gravity foundations.

Gravity Foundation

Gravity foundations are used in shallow depth applications (0–30 m) and consist of a large and heavy base constructed of steel or concrete to rest on the seabed. The footprint is relatively large and may cause scouring, artificial reefs, or physical destruction of habitat upon introduction. Transmission lines also produce an electromagnetic field that may be harmful to some marine organisms.

Gravity Tripod

Gravity tripod foundations are used in transitional depth applications (10–40 m) and consist of two heavy concrete structures connected by three legs, one structure sitting on the seabed while the other is above the water. As of 2013, no offshore windfarms are currently using this foundation. The environmental concerns are identical to those of gravity foundations, though the scouring effect may be less significant depending on the design.

Floating Structure

Floating structure foundations are used in deep depth applications (40–900 m) and consist of a balanced floating structure moored to the seabed with fixed cables. The floating structure may be stabilized using buoyancy, the mooring lines, or a ballast. The mooring lines may cause minor scouring or a potential for collision. Transmission lines also produce an electromagnetic field that may be harmful to some marine organisms.

Geothermal power

Geothermal energy is the heat of the Earth, which can be tapped into to produce electricity in power plants. Warm water produced from geothermal sources can be used for industry, agriculture, bathing and cleansing. Where underground steam sources can be tapped, the steam is used to run a steam turbine. Geothermal steam sources have a finite life as underground water is depleted. Arrangements that circulate surface water through rock formations to produce hot water or steam are, on a human-relevant time scale, renewable.

While a geothermal power plant does not burn any fuel, it will still have emissions due to substances other than steam which come up from the geothermal wells. These may include hydrogen sulfide, and carbon dioxide. Some geothermal steam sources entrain non-soluble minerals that must be removed from the steam before it is used for generation; this material must be properly disposed. Any (closed cycle) steam power plant requires cooling water for condensers; diversion of cooling water from natural sources, and its increased temperature when returned to streams or lakes, may have a significant impact on local ecosystems.

Removal of ground water and accelerated cooling of rock formations can cause earth tremors. Enhanced geothermal systems (EGS) fracture underground rock to produce more steam; such projects can cause earthquakes. Certain geothermal projects (such as one near Basel, Switzerland in 2006) have been suspended or canceled owing to objectionable seismicity induced by geothermal recovery. However, risks associated with "hydrofracturing induced seismicity are low compared to that of natural earthquakes, and can be reduced by careful management and monitoring" and "should not be regarded as an impediment to further development of the Hot Rock geothermal energy resource".

Solar power

Currently solar photovoltaic power is used primarily in Germany and Spain where the governments offer financial incentives. In the U.S., Washington State also provides financial incentives. Photovoltaic power is also more common, as one might expect, in areas where sunlight is abundant.

It works by converting the sun's radiation into direct current (DC) power by use of photovoltaic cells. This power can then be converted into the more common AC power and fed to the power grid.

Solar photovoltaic power offers a viable alternative to fossils fuels for its cleanliness and supply, although at a high production cost. Future technology improvements are expected to bring this cost down to a more competitive range.

Its negative impact on the environment lies in the creation of the solar cells which are made primarily of silica (from sand) and the extraction of silicon from silica may require the use of fossil fuels, although newer manufacturing processes have eliminated CO₂ production. Solar power carries an upfront cost to the environment via production, but offers clean energy throughout the lifespan of the solar cell.

Large scale electricity generation using photovoltaic power requires a large amount of land, due to the low power density of photovoltaic power. Land use can be reduced by installing on buildings and other built up areas, though this reduces efficiency.

Concentrated solar power

Also known as Solar thermal, this technology uses various types of mirrors to concentrate sunlight and produce heat. This heat is used to generate electricity in a standard Rankine cycle turbine. Like most thermoelectric power generation, this consumes water. This can be a problem, as solar powerplants are most commonly located in a desert environment due to the need for sunlight and large amounts of land. Many concentrated solar systems also use exotic fluids to absorb and collect heat while remaining at low pressure. These fluids could be dangerous if spilled.

Negawatt power

Negawatt power refers to investment to reduce electricity consumption rather than investing to increase supply capacity. In this way investing in Negawatts can be considered as an alternative to a new power station and the costs and environmental concerns can be compared.

Negawatt investment alternatives to reduce consumption by improving efficiency include:

• Providing customers with energy efficient lamps - low environmental impact
• Improved thermal insulation and airtightness for buildings - low environmental impact
• Replacing older industrial plant - low environmental impact. Can have a positive impact due to reduced emissions.

Negawatt investment alternatives to reduce peak electrical load by time shifting demand include;

• Storage heaters - older systems had asbestos. Newer systems have low environmental impact.
• Demand response control systems where the electricity board can control certain customer loads - minimal environmental impact
• Thermal storage systems such as Ice storage systems to make ice during the night and store it to use it for air conditioning during the day - minimal environmental impact
• Pumped storage hydroelectricity - Can have a significant environmental impact - see Hydroelectricity.
• other Grid energy storage technologies - impact varies.

Note that time shifting does not reduce total energy consumed or system efficiency however it can be used to avoid the need to build a new power station to cope with a peak load.

SUBSCRIBERS - ( LINKS) :FOLLOW / REF / 2 /

findleverage.blogspot.com

  Krkz77@yahoo.com

  +234-81-83195664